 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1. general description the 74ahc04; 74ahct04 is a high-speed si-gate cmos device and is pin compatible with low-power schottky ttl (lsttl). the device is speci?ed in compliance with jedec standard no. 7a. the 74ahc04; 74ahct04 provides six inverting buffers. 2. features n balanced propagation delays n input accepts voltages higher than v cc n input levels: u cmos levels: 74ahc04 only u ttl levels: 74ahct04 only n esd protection: u hbm eia/jesd22-a114-b exceeds 2000 v u mm eia/jesd22-a115-a exceeds 200 v n speci?ed from - 40 c to +85 c and from - 40 c to +125 c 3. quick reference data [1] c pd is used to determine the dynamic power dissipation (p d in m w): p d =c pd v cc 2 f i n+ ? (c l v cc 2 f o ) where: f i = input frequency in mhz; 74ahc04; 74ahct04 hex inverter rev. 03 7 february 2005 product data sheet table 1: quick reference data gnd = 0 v; t amb =25 c; t r =t f 3.0 ns. symbol parameter conditions min typ max unit type 74ahc04 t phl , t plh propagation delay na to ny c l = 15 pf; v cc = 5 v - 3.0 - ns c i input capacitance v i =v cc or gnd - 3.0 - pf c pd power dissipation capacitance v i = gnd to v cc; c l = 50 pf; f i = 1 mhz [1] - 13.5 - pf type 74ahct04 t phl , t plh propagation delay na to ny c l = 15 pf; v cc = 5 v - 3.0 - ns c i input capacitance v i =v cc or gnd - 3.0 - pf c pd power dissipation capacitance v i = gnd to v cc - 1.5 v; c l = 50 pf; f i = 1 mhz [1] - 13.9 - pf
9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 2 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter f o = output frequency in mhz; c l = output load capacitance in pf; v cc = supply voltage in v; n = number of inputs switching; ? (c l v cc 2 f o ) = sum of outputs. 4. ordering information 5. functional diagram table 2: ordering information type number package temperature range name description version 74ahc04d - 40 c to +125 c so14 plastic small outline package; 14 leads; body width 3.9 mm sot108-1 74ahc04pw - 40 c to +125 c tssop14 plastic thin shrink small outline package; 14 leads; body width 4.4 mm sot402-1 74AHC04BQ - 40 c to +125 c dhvqfn14 plastic dual in-line compatible thermal enhanced very thin quad ?at package; no leads; 14 terminals; body 2.5 3 0.85 mm sot762-1 74ahct04d - 40 c to +125 c so14 plastic small outline package; 14 leads; body width 3.9 mm sot108-1 74ahct04pw - 40 c to +125 c tssop14 plastic thin shrink small outline package; 14 leads; body width 4.4 mm sot402-1 74ahct04bq - 40 c to +125 c dhvqfn14 plastic dual in-line compatible thermal enhanced very thin quad ?at package; no leads; 14 terminals; body 2.5 3 0.85 mm sot762-1 fig 1. logic symbol fig 2. iec logic symbol mna342 1a 1y 1 2 2a 2y 3 4 3a 3y 5 6 4a 4y 9 8 5a 5y 11 10 6a 6y 13 12 1 1 2 mna343 3 1 4 5 1 6 9 1 8 11 1 10 13 1 12 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 3 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter 6. pinning information 6.1 pinning 6.2 pin description fig 3. logic diagram (one inverter) mna341 a y (1) the die substrate is attached to the exposed die pad using conductive die attach material. it can not be used as a supply pin or input. fig 4. pin con?guration so14 and tssop14 fig 5. pin con?guration dhvqfn14 04 1a v cc 1y 6a 2a 6y 2y 5a 3a 5y 3y 4a gnd 4y 001aac441 1 2 3 4 5 6 7 8 10 9 12 11 14 13 001aac442 04 gnd (1) transparent top view 3y 4a 3a 5y 2y 5a 2a 6y 1y 6a gnd 4y 1a v cc 6 9 5 10 4 11 3 12 2 13 7 8 1 14 terminal 1 index area table 3: pin description symbol pin description 1a 1 data input 1y 2 data output 2a 3 data input 2y 4 data output 3a 5 data input 3y 6 data output gnd 7 ground (0 v) 4y 8 data output 4a 9 data input 5y 10 data output 5a 11 data input 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 4 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter 7. functional description 7.1 function table [1] h = high voltage level; l = low voltage level. 8. limiting values [1] the input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] for so14 packages: above 70 c the value of p tot derates linearly with 8 mw/k. for tssop14 packages: above 60 c the value of p tot derates linearly with 5.5 mw/k. for dhvqfn14 packages: above 60 c the value of p tot derates linearly with 4.5 mw/k. 6y 12 data output 6a 13 data input v cc 14 supply voltage table 3: pin description continued symbol pin description table 4: function table [1] input na output ny lh hl table 5: limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (groun d=0v). symbol parameter conditions min max unit v cc supply voltage - 0.5 +7.0 v v i input voltage range - 0.5 +7.0 v i ik input diode current v i < - 0.5 v [1] - - 20 ma i ok output diode current v o < - 0.5 v or v o >v cc + 0.5 v [1] - 20 ma i o output source or sink current - 0.5 v < v o 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 6 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter v ol low-level output voltage v i =v ih or v il i o =50 m a; v cc = 2.0 v - 0 0.1 v i o =50 m a; v cc = 3.0 v - 0 0.1 v i o =50 m a; v cc = 4.5 v - 0 0.1 v i o = 4.0 ma; v cc = 3.0 v - - 0.36 v i o = 8.0 ma; v cc = 4.5 v - - 0.36 v i li input leakage current v i =v cc or gnd; v cc = 5.5 v - - 0.1 m a i oz 3-state output off-state current v i =v ih or v il ; v o =v cc or gnd; v cc = 5.5 v -- 0.25 m a i cc quiescent supply current v i =v cc or gnd; i o =0a; v cc = 5.5 v - - 4.0 m a c i input capacitance v i =v cc or gnd - 3 10 pf t amb = - 40 c to +85 c v ih high-level input voltage v cc = 2.0 v 1.5 - - v v cc = 3.0 v 2.1 - - v v cc = 5.5 v 3.85 - - v v il low-level input voltage v cc = 2.0 v - - 0.5 v v cc = 3.0 v - - 0.9 v v cc = 5.5 v - - 1.65 v v oh high-level output voltage v i =v ih or v il i o = - 50 m a; v cc = 2.0 v 1.9 - - v i o = - 50 m a; v cc = 3.0 v 2.9 - - v i o = - 50 m a; v cc = 4.5 v 4.4 - - v i o = - 4.0 ma; v cc = 3.0 v 2.48 - - v i o = - 8.0 ma; v cc = 4.5 v 3.8 - - v v ol low-level output voltage v i =v ih or v il i o =50 m a; v cc = 2.0 v - - 0.1 v i o =50 m a; v cc = 3.0 v - - 0.1 v i o =50 m a; v cc = 4.5 v - - 0.1 v i o = 4.0 ma; v cc = 3.0 v - - 0.44 v i o = 8.0 ma; v cc = 4.5 v - - 0.44 v i li input leakage current v i =v cc or gnd; v cc = 5.5 v - - 1.0 m a i oz 3-state output off-state current v i =v ih or v il ; v o =v cc or gnd; v cc = 5.5 v -- 2.5 m a i cc quiescent supply current v i =v cc or gnd; i o =0a; v cc = 5.5 v --40 m a c i input capacitance v i =v cc or gnd - - 10 pf t amb = - 40 c to +125 c v ih high-level input voltage v cc = 2.0 v 1.5 - - v v cc = 3.0 v 2.1 - - v v cc = 5.5 v 3.85 - - v table 7: static characteristics type 74ahc04 continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min typ max unit 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 7 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter v il low-level input voltage v cc = 2.0 v - - 0.5 v v cc = 3.0 v - - 0.9 v v cc = 5.5 v - - 1.65 v v oh high-level output voltage v i =v ih or v il i o = - 50 m a; v cc = 2.0 v 1.9 - - v i o = - 50 m a; v cc = 3.0 v 2.9 - - v i o = - 50 m a; v cc = 4.5 v 4.4 - - v i o = - 4.0 ma; v cc = 3.0 v 2.40 - - v i o = - 8.0 ma; v cc = 4.5 v 3.70 - - v v ol low-level output voltage v i =v ih or v il i o =50 m a; v cc = 2.0 v - - 0.1 v i o =50 m a; v cc = 3.0 v - - 0.1 v i o =50 m a; v cc = 4.5 v - - 0.1 v i o = 4.0 ma; v cc = 3.0 v - - 0.55 v i o = 8.0 ma; v cc = 4.5 v - - 0.55 v i li input leakage current v i =v cc or gnd; v cc = 5.5 v - - 2.0 m a i oz 3-state output off-state current v i =v ih or v il ; v o =v cc or gnd; v cc = 5.5 v -- 10.0 m a i cc quiescent supply current v i =v cc or gnd; i o =0a; v cc = 5.5 v --80 m a c i input capacitance v i =v cc or gnd - - 10 pf table 7: static characteristics type 74ahc04 continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min typ max unit table 8: static characteristics type 74ahct04 at recommended operating conditions; voltage are referenced to gnd (ground = 0 v). symbol parameter conditions min typ max unit t amb = 25 c v ih high-level input voltage v cc = 4.5 v to 5.5 v 2.0 - - v v il low-level input voltage v cc = 4.5 v to 5.5 v - - 0.8 v v oh high-level output voltage v i =v ih or v il i o = - 50 m a; v cc = 4.5 v 4.4 4.5 - v i o = - 8.0 ma; v cc = 4.5 v 3.94 - - v v ol low-level output voltage v i =v ih or v il i o =50 m a; v cc = 4.5 v - 0 0.1 v i o = 8.0 ma; v cc = 4.5 v - - 0.36 v i li input leakage current v i =v ih or v il ; v cc = 5.5 v - - 0.1 m a i oz 3-state output off-state current v i =v ih or v il ; v o =v cc or gnd per input pin; other inputs at v cc or gnd; i o = 0 a; v cc = 5.5 v -- 0.25 m a i cc quiescent supply current v i =v cc or gnd; i o =0a; v cc = 5.5 v - - 4.0 m a 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 8 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter d i cc additional quiescent supply current per input pin v i =v cc - 2.1 v and other inputs at v cc or gnd; i o =0a; v cc = 4.5 v to 5.5 v - - 1.35 ma c i input capacitance v i =v cc or gnd - 3 10 pf t amb = - 40 c to +85 c v ih high-level input voltage v cc = 4.5 v to 5.5 v 2.0 - - v v il low-level input voltage v cc = 4.5 v to 5.5 v - - 0.8 v v oh high-level output voltage v i =v ih or v il i o = - 50 m a; v cc = 4.5 v 4.4 - - v i o = - 8.0 ma; v cc = 4.5 v 3.8 - - v v ol low-level output voltage v i =v ih or v il i o =50 m a; v cc = 4.5 v - - 0.1 v i o = 8.0 ma; v cc = 4.5 v - - 0.44 v i li input leakage current v i =v ih or v il ; v cc = 5.5 v - - 1.0 m a i oz 3-state output off-state current v i =v ih or v il ; v o =v cc or gnd per input pin; other inputs at v cc or gnd; i o = 0 a; v cc = 5.5 v -- 2.5 m a i cc quiescent supply current v i =v cc or gnd; i o =0a; v cc = 5.5 v --40 m a d i cc additional quiescent supply current per input pin v i =v cc - 2.1 v other inputs at v cc or gnd; i o =0a;v cc = 4.5 v to 5.5 v - - 1.5 ma c i input capacitance v i =v cc or gnd - - 10 pf t amb = - 40 c to +125 c v ih high-level input voltage v cc = 4.5 v to 5.5 v 2.0 - - v v il low-level input voltage v cc = 4.5 v to 5.5 v - - 0.8 v v oh high-level output voltage v i =v ih or v il i o = - 50 m a; v cc = 4.5 v 4.4 - - v i o = - 8.0 ma; v cc = 4.5 v 3.70 - - v v ol low-level output voltage v i =v ih or v il i o =50 m a; v cc = 4.5 v - - 0.1 v i o = 8.0 ma; v cc = 4.5 v - - 0.55 v i li input leakage current v i =v ih or v il ; v cc = 5.5 v - - 2.0 m a i oz 3-state output off-state current v i =v ih or v il ; v o =v cc or gnd per input pin; other inputs at v cc or gnd; i o = 0 a; v cc = 5.5 v -- 10.0 m a i cc quiescent supply current v i =v cc or gnd; i o =0a; v cc = 5.5 v --80 m a d i cc additional quiescent supply current per input pin v i =v cc - 2.1 v and other inputs at v cc or gnd; i o =0a; v cc = 4.5 v to 5.5 v - - 1.5 ma c i input capacitance v i =v cc or gnd - - 10 pf table 8: static characteristics type 74ahct04 continued at recommended operating conditions; voltage are referenced to gnd (ground = 0 v). symbol parameter conditions min typ max unit 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 9 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter 11. dynamic characteristics [1] typical values are measured at v cc = 3.3 v. [2] typical values are measured at v cc = 5.0 v. [3] c pd is used to determine the dynamic power dissipation (p d in m w): p d =c pd v cc 2 f i n+ ? (c l v cc 2 f o ) where: f i = input frequency in mhz; f o = output frequency in mhz; c l = output load capacitance in pf; v cc = supply voltage in v; n = number of inputs switching; ? (c l v cc 2 f o ) = sum of outputs. table 9: dynamic characteristics type 74ahc04 gnd = 0 v; t r =t f 3.0 ns; for waveform see figure 6 ; for test circuit see figure 7 . symbol parameter conditions min typ max unit t amb = 25 c t phl , t plh propagation delay na to ny v cc = 3.0 v to 3.6 v [1] c l = 15 pf - 4.0 8.5 ns c l = 50 pf - 6.0 11.4 ns v cc = 4.5 v to 5.5 v [2] c l = 15 pf - 3.0 5.5 ns c l = 50 pf - 4.5 7.5 ns c pd power dissipation capacitance v i = gnd to v cc; c l = 50 pf; f i = 1 mhz [3] - 13.5 - pf t amb = - 40 c to +85 c t phl , t plh propagation delay na to ny v cc = 3.0 v to 3.6 v c l = 15 pf 1.0 - 10.5 ns c l = 50 pf 1.0 - 13 ns v cc = 4.5 v to 5.5 v c l = 15 pf 1.0 - 6.5 ns c l = 50 pf 1.0 - 8.5 ns t amb = - 40 c to +125 c t phl , t plh propagation delay na to ny v cc = 3.0 v to 3.6 v c l = 15 pf 1.0 - 11.0 ns c l = 50 pf 1.0 - 14.5 ns v cc = 4.5 v to 5.5 v c l = 15 pf 1.0 - 7.0 ns c l = 50 pf 1.0 - 9.5 ns 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 10 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter [1] typical values are measured at v cc = 5.0 v. [2] c pd is used to determine the dynamic power dissipation (p d in m w): p d =c pd v cc 2 f i n+ ? (c l v cc 2 f o ) where: f i = input frequency in mhz; f o = output frequency in mhz; c l = output load capacitance in pf; v cc = supply voltage in v; n = number of inputs switching; ? (c l v cc 2 f o ) = sum of outputs. 12. waveforms table 10: dynamic characteristics type 74ahct04 gnd = 0 v; t r =t f 3.0 ns; for waveform see figure 6 ; for test circuit see figure 7 . symbol parameter conditions min typ max unit t amb = 25 c t phl , t plh propagation delay na to ny v cc = 4.5 v to 5.5 v [1] c l = 15 pf - 3.0 6.7 ns c l = 50 pf - 4.5 7.7 ns c pd power dissipation capacitance v i = gnd to v cc - 1.5 v; c l = 50 pf; f i = 1 mhz [2] - 13.9 - pf t amb = - 40 c to +85 c t phl , t plh propagation delay na to ny v cc = 4.5 v to 5.5 v c l = 15 pf 1.0 - 7.5 ns c l = 50 pf 1.0 - 8.5 ns t amb = - 40 c to +125 c t phl , t plh propagation delay na to ny v cc = 4.5 v to 5.5 v c l = 15 pf 1.0 - 8.5 ns c l = 50 pf 1.0 - 10.0 ns measurement points are given in t ab le 11 . v oh and v ol are typical output voltage drop that occur with the output load. fig 6. the input (na) to output (ny) propagation delay mna344 t phl t plh v m v m na input ny output gnd v i v oh v ol 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 11 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter table 11: measurement points type input output v m v m 74ahc04 0.5v cc 0.5v cc 74ahct04 1.5 v 0.5v cc test data is given in t ab le 12 . de?nitions: c l = load capacitance including jig and probe capacitance. r t = termination resistance should be equal to output impedance z o of the pulse generator. fig 7. load circuitry for switching times table 12: test data type input load v i t r , t f c l 74ahc04 v cc 3.0 ns 15 pf or 50 pf 74ahct04 3.0 v 3.0 ns 15 pf or 50 pf mna101 v cc v i v o r t c l pulse generator d.u.t. 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 12 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter 13. package outline fig 8. package outline sot108-1 (so14) unit a max. a 1 a 2 a 3 b p cd (1) e (1) (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 8.75 8.55 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 0 o o 0.25 0.1 dimensions (inch dimensions are derived from the original mm dimensions) note 1. plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 sot108-1 x w m q a a 1 a 2 b p d h e l p q detail x e z e c l v m a (a ) 3 a 7 8 1 14 y 076e06 ms-012 pin 1 index 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.35 0.34 0.16 0.15 0.05 1.05 0.041 0.244 0.228 0.028 0.024 0.028 0.012 0.01 0.25 0.01 0.004 0.039 0.016 99-12-27 03-02-19 0 2.5 5 mm scale so14: plastic small outline package; 14 leads; body width 3.9 mm sot108-1 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 13 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter fig 9. package outline sot402-1 (tssop14) unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.72 0.38 8 0 o o 0.13 0.1 0.2 1 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot402-1 mo-153 99-12-27 03-02-18 w m b p d z e 0.25 17 14 8 q a a 1 a 2 l p q detail x l (a ) 3 h e e c v m a x a y 0 2.5 5 mm scale tssop14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm sot402-1 a max. 1.1 pin 1 index 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 14 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter fig 10. package outline sot762-1 (dhvqfn14) terminal 1 index area 0.5 1 a 1 e h b unit y e 0.2 c references outline version european projection issue date iec jedec jeita mm 3.1 2.9 d h 1.65 1.35 y 1 2.6 2.4 1.15 0.85 e 1 2 0.30 0.18 0.05 0.00 0.05 0.1 dimensions (mm are the original dimensions) sot762-1 mo-241 - - - - - - 0.5 0.3 l 0.1 v 0.05 w 0 2.5 5 mm scale sot762-1 dhvqfn14: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 14 terminals; body 2.5 x 3 x 0.85 mm a (1) max. a a 1 c detail x y y 1 c e l e h d h e e 1 b 26 13 9 8 7 1 14 x d e c b a 02-10-17 03-01-27 terminal 1 index area a c c b v m w m e (1) note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. d (1) 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 15 of 17 philips semiconductors 74ahc04; 74ahct04 hex inverter 14. revision history table 13: revision history document id release date data sheet status change notice doc. number supersedes 74ahc_ahct04_3 20050207 product data sheet - 9397 750 14503 74ahc_ahct04_2 modi?cations: ? the format of this data sheet is redesigned to comply with the current presentation and information standard of philips semiconductors. ? added: type numbers 74AHC04BQ and 74ahct04bq (dhvqfn14 package). 74ahc_ahct04_2 19990927 product speci?cation - 9397 750 06286 74ahc_ahct04_1 74ahc_ahct04_1 19990225 product speci?cation - 9397 750 05326 - philips semiconductors 74ahc04; 74ahct04 hex inverter 9397 750 14503 ? koninklijke philips electronics n.v. 2005. all rights reserved. product data sheet rev. 03 7 february 2005 16 of 17 15. data sheet status [1] please consult the most recently issued data sheet before initiating or completing a design. [2] the product status of the device(s) described in this data sheet may have changed since this data sheet was published. the l atest information is available on the internet at url http://www.semiconductors.philips.com. [3] for data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 16. de?nitions short-form speci?cation the data in a short-form speci?cation is extracted from a full data sheet with the same type number and title. for detailed information see the relevant data sheet or data handbook. limiting values de?nition limiting values given are in accordance with the absolute maximum rating system (iec 60134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the speci?cation is not implied. exposure to limiting values for extended periods may affect device reliability. application information applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors make no representation or warranty that such applications will be suitable for the speci?ed use without further testing or modi?cation. 17. disclaimers life support these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips semiconductors for any damages resulting from such application. right to make changes philips semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. when the product is in full production (status production), relevant changes will be communicated via a customer product/process change noti?cation (cpcn). philips semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise speci?ed. 18. contact information for additional information, please visit: http://www.semiconductors.philips.com for sales of?ce addresses, send an email to: sales.addresses@www.semiconductors.philips.com level data sheet status [1] product status [2] [3] de?nition i objective data development this data sheet contains data from the objective speci?cation for product development. philips semiconductors reserves the right to change the speci?cation in any manner without notice. ii preliminary data quali?cation this data sheet contains data from the preliminary speci?cation. supplementary data will be published at a later date. philips semiconductors reserves the right to change the speci?cation without notice, in order to improve the design and supply the best possible product. iii product data production this data sheet contains data from the product speci?cation. philips semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. relevant changes will be communicated via a customer product/process change noti?cation (cpcn). ? koninklijke philips electronics n.v. 2005 all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. date of release: 7 february 2005 document number: 9397 750 14503 published in the netherlands philips semiconductors 74ahc04; 74ahct04 hex inverter 19. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 quick reference data . . . . . . . . . . . . . . . . . . . . . 1 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 6 pinning information . . . . . . . . . . . . . . . . . . . . . . 3 6.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 6.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 7 functional description . . . . . . . . . . . . . . . . . . . 4 8 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 9 recommended operating conditions. . . . . . . . 5 10 static characteristics. . . . . . . . . . . . . . . . . . . . . 5 11 dynamic characteristics . . . . . . . . . . . . . . . . . . 9 12 waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 13 package outline . . . . . . . . . . . . . . . . . . . . . . . . 12 14 revision history . . . . . . . . . . . . . . . . . . . . . . . . 15 15 data sheet status . . . . . . . . . . . . . . . . . . . . . . . 16 16 de?nitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 17 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 18 contact information . . . . . . . . . . . . . . . . . . . . 16 |
Price & Availability of 74AHC04BQ
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |